Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateCraftsman Torsion Spring Replacement: The Mesquite Owner’s Guide
We replace Craftsman torsion springs in Mesquite for a typical installed price of $180 to $340, and we can often get to a broken spring the same day you call. A live person answers (844) 320-6569 around the clock, quotes the job on that call, and holds the number when we get there.

Most Mesquite owners find out the hard way. You hit the opener, the motor hums, and nothing moves. Sometimes you hear the bang from the garage first – a sharp crack that sounds like a shot. Then the door won’t budge, the car is sealed inside, and you’re standing in the driveway looking at a gap. That’s usually the torsion spring letting go. It’s the single part that carries most of a 200-pound door’s weight, and when it breaks, nothing else can lift the door safely.
Key takeaways:
- Craftsman torsion springs are matched to door weight and height, not just the brand name.
- Installed replacement in Mesquite runs $180 to $340, quoted before we start.
- These springs store dangerous tension. This is not a job to take on yourself.
- We’re an independent Mesquite shop, not affiliated with Craftsman, and we work on their doors every week.
Which Craftsman Models This Applies To
Craftsman sold garage doors and door hardware through Sears for decades, so the brand name alone doesn’t tell us the spring you need. What matters is the door, not the logo on the opener. Craftsman torsion springs get sized by wire gauge, inside diameter, and overall length, and those numbers have to match the actual weight and height of your door. A single-car door and a double-car door use very different springs. So do insulated and uninsulated panels.
Here’s the part most homeowners don’t realize: the spring on your door may not be a “Craftsman” spring at all. A lot of Craftsman-labeled doors shipped with standard torsion hardware sized to the door’s specs, and over the years plenty of them got swapped with whatever a previous tech grabbed. That’s fine as long as the replacement matches. It’s a problem when someone guesses.
To identify the right part, we look at the door’s ID label (often inside the frame or on the end stile) and then measure the old spring directly – wire size with a gauge, coil count, and inside diameter. That’s where the aftermarket decision comes in. A quality aftermarket spring built to the correct spec performs the same as an OEM replacement and usually costs less. We’ll tell you which we’re installing and why.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Craftsman Torsion Spring Replacement Is Failing
Springs rarely fail without warning. If you know what to look for, you can catch one before it strands your car. Here’s what we see most in Mesquite:
- The door won’t lift, but the opener runs. If the motor hums and the door stays put, the spring has likely snapped or lost its wind. The opener is doing its job – there’s just no counterbalance left.
- A visible gap in the coil. Look at the spring above the door (never touch it). A clean break in the winding means it’s done. This is the clearest sign there is.
- Loud bang from the garage. When a torsion spring breaks under load, it releases all at once. That crack you heard is the sound of it letting go.
- The door feels heavy when you lift it by hand. A balanced door should lift with light effort. If it feels like dead weight, the spring is weak or broken, and forcing it strains the opener and the cables.
- The door drifts or slams. A door that won’t stay halfway open, or drops the last foot, is out of balance – often the first stage of spring wear.
One local note: our dry desert air and big temperature swings are hard on metal. We regularly see springs in Mesquite fail earlier than the manufacturer’s estimate because of that constant expansion and contraction. A spring rated for 10,000 cycles might give you fewer here. When we’re out, we’ll count the cycles left on yours the way you’d check tread on a tire.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Torsion spring replacement in Mesquite typically runs $180 to $340 installed. That range covers the spring itself, the labor to wind it safely, and a balance check on the door before we leave. Where you land in that range depends on a few things:

- One spring or two. Many doors use a pair. Replacing both at once is usually the smarter move when one has already broken.
- Door size and weight. A heavier insulated double door needs a bigger spring than a light single.
- Spring type and grade. A standard-cycle spring sits at the low end. A high-cycle spring built to last longer costs more up front but often makes sense for a door that gets used heavily.
The price we quote on the phone is the price on the invoice. We don’t revise it upward when we see the door. Every job carries our 90-Day Done Right Promise in writing – if something isn’t right, one call brings us back, no runaround. And right now, repairs over $200 get $40 off, with a standing 10% discount for seniors and veterans.
DIY or Call Us?
Some things you can safely check yourself. You can look at the spring for a visible gap, listen for the opener running without the door moving, and test whether the door feels unusually heavy. That’s looking, not touching.
What you shouldn’t do is try to replace a torsion spring yourself. This is the honest part: a torsion spring holds serious stored energy, and winding one wrong can cause a bad injury in a hurry. A door is 200 pounds riding on two springs, and there’s no safe shortcut around the tools and know-how it takes to wind them correctly. People get hurt doing exactly this. We’d rather you never take that chance.
If your Craftsman door is down, call (844) 320-6569. We’ll quote it on the call, and I’ll be there myself – the name on the van is the name on the license. We also service LiftMaster, Chamberlain, and Genie doors while we’re at it.
FAQs
Most torsion springs are rated for about 10,000 open-and-close cycles, which works out to roughly 7 to 10 years for a typical household. In Mesquite’s dry heat and big temperature swings, we see plenty fail toward the shorter end of that. If your door gets heavy use or your spring is already past that window, it’s worth a look before it breaks.
No – once a torsion spring cracks, it can’t be safely repaired and has to be replaced. There’s no reliable way to mend a broken coil that holds tension. The good news is replacement is a straightforward job for us. Call (844) 320-6569 for an exact quote – estimates are free.
Most single-spring replacements take about an hour, and a pair takes a bit longer. We balance and test the door before we leave so you know it’s working right. We can often get to a broken spring in Mesquite the same day you call – a live person answers any hour at (844) 320-6569.
We measure the old spring directly and match it to your door’s weight and height – wire gauge, coil count, and inside diameter, not just the brand name. Craftsman doors were built on standard torsion hardware, so a correctly spec’d spring works whether it’s OEM or a quality aftermarket equivalent. We’ll tell you which we’re installing and why.
When your Craftsman door won’t lift because the torsion spring gave out, don’t force it and don’t take chances with all that stored tension. Give us a call at (844) 320-6569 for a free estimate. I’ll quote it on the call, hold the number at the door, and back it with our 90-Day Done Right Promise in writing. Locally owned and owner-operated in Mesquite, accountable to the neighbors we see every week.
Written by the team at Otto’s Garage Door Mesquite, serving Mesquite and nearby areas.