Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateClopay Weather Seal Replacement: The Mesquite Owner’s Guide
We replace worn Clopay-compatible weather seals on Mesquite garage doors for $150 – $600 installed, depending on door width and seal style. Most standard single doors land near the low end; wide doubles and threshold-plus-sides jobs climb from there. A failed seal is usually discovered by a cold draft at your ankles, a hornet nest in the gap, or a visible sag between the door bottom and the concrete.

If you can see daylight under the door, the seal is past its working life. Waiting only lets the gap grow.
Which Clopay Models This Applies To
Most Clopay residential doors in Mesquite fall into three families: the Classic and Gallery steel lines, the Coachman wood-grain series, and the Avante aluminum doors. Each uses a different bottom-seal profile. Classic and Gallery typically take a T-style vinyl astragal in 2″, 3″, or 4″ widths. Coachman often uses a similar T-style but in a different hardness. Avante and full-view doors need a slimmer aluminum-retained seal so it doesn’t interfere with the glass panel clearance.
Find your door’s model label inside the jamb and measure the existing seal width and the door thickness before ordering. Sizes are not interchangeable between families, and one millimeter of excess can cause binding. On aftermarket versus OEM: we source quality aftermarket seals that match Clopay specs for the common lines because OEM ordering can add days to a job, but on the aluminum and Coachman doors we recommend the Clopay-compatible profile to keep the track clearance correct.
Otto’s Garage Door Mesquite is an independent service provider. We are not affiliated with Clopay.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Clopay Weather Seal Replacement Is Failing
- Visible daylight under the door. The seal has compressed or torn, and the gap is allowing air, dust, and pests in.
- Hard, cracking, or chalky rubber. Mesquite’s summer heat and low humidity dry out vinyl and EPDM faster than a milder climate ever would. Expect seven to ten years max on a south-facing door here.
- Snagged or dragging bottom edge. The seal is binding against the track or the threshold, usually because the door is slightly out of level or the seal profile is wrong for the door.
- Water pooling inside the garage after a wash-down or rare rain. A hardened seal won’t conform to the concrete, so water and debris slide under.
- Pests or drafts. Ants, scorpions, and field mice in Mesquite use any gap they can find. If you’re sweeping them out weekly, the seal is the entry point.
Each of these is fixable. The tricky part is matching the right seal profile. If you’re not sure, snap a photo of the bottom of the door and call (844) 320-6569. Otto will tell you what he thinks you need.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what the installed price covers on a standard Clopay bottom seal in Mesquite:
- Standard single-car door, vinyl T-seal: $150 – $250
- Double-car door, vinyl T-seal: $220 – $400
- Aluminum-retained seal, Avante or full-view: $300 – $500
- Threshold seal plus side and top seals: $400 – $600
What drives the range: door width, seal profile, whether the bottom retainer needs adjustment, and whether the door is level. Labor is included in those numbers. The part itself is often $30 to $80 depending on profile and width. The rest is getting it seated right and testing the door travel. Every job is quoted before we touch anything, and the price doesn’t change when we pull up.
Our 90-Day Done Right Promise covers the install. If the seal fails or isn’t seated right, one call brings us back.
DIY or Call Us?
You can safely check the bottom seal yourself. Slide your hand along the bottom edge with the door closed and feel for soft spots, cracks, or gaps. Look for daylight. Measure the width and door thickness. That’s the diagnostic part.
The actual swap is where it gets harder. The bottom retainer often needs loosening, the old seal can be glued or crimped in place, and if the retainer is rusty or the door is out of level, you can spend an afternoon fighting it only to end up with a seal that binds on the way down. We’ve seen more than a few Mesquite jobs where the homeowner got halfway through and called us to put it right.
Below is what it looks like from our side:
- Loosen the retainer bolts at both ends of the door bottom.
- Pull the old seal out, clean the channel, and check for rust.
- Slide the new seal in, re-tighten the retainer, and adjust the limit travel.
- Run the door up and down three times, check the seal contact along the floor, and adjust the bottom bracket if needed.
No part of this seal work carries the spring or cable risk of a torsion replacement. It’s the one bottom-of-door job a careful homeowner can attempt. But if you’re not sure of the profile match, don’t guess. Call (844) 320-6569 and Otto will tell you whether it’s a two-minute phone call or a job for us. We’ll give you a free second opinion on any written estimate, and there’s no trip charge anywhere in the county.
FAQs
Plan on seven to ten years on a south-facing door and ten to twelve on a shaded one. Mesquite’s summers dry out vinyl and EPDM fast, and a south wall in July will bake a seal harder than a Phoenix one with more shade. If your door faces west or south, expect the shorter end of that range. Call (844) 320-6569 and Otto will tell you what he sees on your door.
Almost never worth it. The rubber is the part that fails, and a patched or glued seal breaks again within a season. Replacing the full length is the right call, and it’s not much more than the repair would cost. Call (844) 320-6569 for a straight price.
Most standard bottom-seal replacements are done in 45 minutes to an hour on site. Wider doors, aluminum-retained seals, and jobs that need the retainer adjusted can run two hours. We’ll tell you on the phone which it is before you commit. Call (844) 320-6569 to book it.
We match your Clopay door’s profile, not just its width. A T-style 2″ seal from one brand won’t fit another brand’s track clearance, and forcing it causes binding that shortens the seal’s life. We source quality aftermarket seals for the common Clopay lines and Clopay-compatible profiles for the aluminum and Coachman doors. Call (844) 320-6569 and we’ll tell you exactly what your door needs.
If that draft, that sag, or that scorpion sighting has you ready to fix it, call (844) 320-6569. Otto answers the phone, quotes the job on that call, and holds the price when he pulls up. We’re an independent service provider, not affiliated with Clopay, and we’ve been doing this work in Mesquite for Mesquite homeowners since 2004. Our technicians have up to 22 years of experience, and we know exactly what a Mesquite summer does to a weather seal.
Written by the team at Otto’s Garage Door Mesquite, serving Mesquite and nearby areas.